Klover Products Inc.

5807 W Fenrick Rd 53548 Janesville, WI
Phone:
  • Koss Pro4aa Headphones
  • Remote Audio HN7506 Headphones
  • KK-16 Flight Case
  • KK-16 Flight Case - Open
  • KK-16 Flight Case - Loaded with Klover MiK 16
  • KMEQ Equalized XLR microphone
 
Loading...

Klover MiK 16 Kit

$1,819.00$2,719.00

Our KM-16 kits combine our mid-size parabolic microphone with the most commonly used accessories.  Any one of these kits will provide everything you need to begin capturing audio from long distances.

The kit includes one Klover MiK 16 parabolic microphone (KM-16) as well as one of each accessory listed below:

Clear
SKU: N/A Categories: ,

LEARN MORE

The Klover MiK 16 is our mid-size parabolic microphone.  It turns your omni-directional mic into a long-range microphone that gathers audio from long distances.   This long-distance microphone is capable of capturing conversations from up to 300 feet.

Klover MiK 09 LED Kit
Klover Mik 26 Tactical Kit

SHIPPING INFORMATION

Weight 12 lbs
Dimensions 21 x 21 x 9 in
Order Processing

Normally 3 to 5 days, cases may take up to 25 days. Contact us for current stock status.

Product Code

B

Specifications

Klover MiK 16 Specifications:

  • Range: 250 to 300 feet
  • Microphone pickup pattern: Omnidirectional or cardioid pattern
  • Microphone: 20mm Diameter or lavaliere
  • Dish outside diameter: 16″
  • Parabolic diameter: 13.5″
  • Weight: Approximately 2 lbs
  • Overall dimensions: 18” x 16” x 10” (w Handle)
Klover MiK 09 LED Kit
Klover Mik 26 Tactical Kit

Amplifiers

Sound Devices MM-1 Specifications

  • Gain: (Mic – Line): 0 dB to 66 dB input to output, switch selectable
  • Frequency Response: (Mic – Line) 20 Hz –20 kHz, +0.1, -0.5 dB, -1 dB at 50 kHz (relative to 1 kHz level with 150 ohm source)
  • Equivalent Input Noise: (Mic) -126 dBu (-128 dBV) maximum (150 ohm source, flat weighting, 22 Hz – 22 kHz bandwidth gain setting 36 dB or greater)
  • Dynamic Range: (Mic to Line) 122 dB minimum at the +18 dB gain setting
  • THD + Noise: 0.05% maximum (from 50 Hz – 22 kHz @ +4 dBu output level, 22 Hz – 22 kHz filter bandwidth, +46 dB gain setting
  • Gain Accuracy: (Mic – Line) +0.6, -0.1 dB with reference to front panel gain markings (150 ohm source, 100 k load impedances)
  • Output Clipping Level: (Line) +22 dBu minimum with 100k ohm load+20 dBu minimum with 600 ohm load
  • Input Clipping Level: (Mic) +4 dBu minimum at the 0 or +18 dB gain setting
  • Common Mode Rejection Ratio: 100 dB minimum at 80 Hz60 dB minimum at 10 kHzMaximum of 66 dB of gain, in eleven discrete steps
  • Dynamic range exceeding 120 dB
  • 10 Hz to 50 kHz audio bandwidth
  • High immunity to RF interference
  • High current line output driver
  • Transformer-balanced input and output
  • Extended range peak limiter via dual opto-isolators makes preamplifier virtually “unclippable”
  • Selectable 48-volt / 12-volt phantom power or 12-volt “T” power
  • High-pass filter @ 80 or 160 Hz, 6 dB per octave
  • Headphone monitoring of microphone audio, monitor audio, or a mix of both
  • Monitor input accepts mono, balanced or unbalanced line-level inputs on 1/4-inch tip-ring-sleeve connector
  • Separate level control of Monitor gain and overall headphone gain
  • Split ear function via DIP switches
  • Internal battery power (two-AA)
  • Excellent battery life with alkaline and NiMH rechargeable batteries
  • External 5-17 VDC powering
  • High-strength aluminum chassis with durable belt clip
  • Dimensions: 1.95″ x 3.75″ x 6.55″
  • Weight: 1 lb
Whirlwind MD-1 Specifications

  • A separate balanced line level Aux input to the headphone amp for monitoring a program mix, a console foldback or a director’s cues
  • Headphone volume control and a separate MIX control allow you to adjust the headphone balance between the mic driver section and Aux input
  • Built-in 18V phantom power (switchable)
  • Steel case with belt clip resists abuse
  • Two alkaline 9V batteries are mounted in slide out trays for easy accessInput Impedance: Mic Mode: 1.5k Ohms, Line Mode: 10k Ohms
  • Output Impedance: 600 Ohms
  • Max Input Signal: Mic Mode: -4dBm, Line Mode: +12dBm
  • Frequency Response: ±3dBm, 6Hz-25kHz, -2dBm @ 20Hz, -1dBm @ 20kHz
  • Maximum Output Level:  +15dB into 2k Ohms, +26dB into 10k Ohms, +34dB into 100k Ohms
  • Phantom Power: +18VDC
  • Power Requirements: (2) 9V alkaline batteries
  • Dimensions: 2.25″ x 3.88″ x 6.25″
  • Weight: 2 lb
Klover MiK 09 LED Kit
Klover Mik 26 Tactical Kit

Microphones

Sennheiser MKE2 Specifications

  • Frequency Response: 20Hz to 20kHz +- 3dB
  • Polar Pattern: Omnidirectional
  • Sensitivity (free field, no load) (1 kHz): 10 mV/Pa ±2.5 dB
  • Equivalent Acoustic Noise: 24dB SPL A-Weighted
  • Maximum Sound Pressure: 150 dB (48V, 1mV/Pa mike)
  • Power Requirements: 9V to 48V Phantom (4mA @ 48V)
  • Output Impedance: 600 ohms, balanced
  • Output Connector: XLR-3 Male
  • Dimensions: .23″ x .18″ (5.8mm x 4.6mm)
  • Weight: .012 oz (.34 g)
Countryman B3 Specifications

  • Water/Weather Resistant
  • Frequency Response: 20 Hz to 20 kHz
  • Polar Pattern: Omnidirectional
  • Power Requirements: Phantom: 9V to 48V (4mA at 48V)
  • Sensitivity: W4 (no band): 12.0 mV/Pascal (-38 dB re 1V/Pa)
  • Equivalent Acoustic Noise: 24 dBA
  • Overload Sound Level: Phantom: 150 dBA SPL
  • Cable Length:  5 Feet
  • Output Connector: XLR-3 Male
  • Weight: 0.012 oz (0.34 g)
  • Dimensions: 0.23″ x 0.18″ (5.8mm x 4.6mm)
Klover Equalized Mic Specifications

This microphone is a custom built version of the Countryman B3 which is equalized for our parabolic microphones.

  • Water/Weather Resistant
  • Frequency Response: 20 Hz to 20 kHz
  • Polar Pattern: Omnidirectional
  • Power Requirements: Phantom: 9V to 48V (4mA at 48V)
  • Sensitivity: W4 (no band): 12.0 mV/Pascal (-38 dB re 1V/Pa)
  • Equivalent Acoustic Noise: 24 dBA
  • Overload Sound Level: Phantom: 150 dBA SPL
  • Cable Length:  5 Feet
  • Output Connector: XLR-3 Male
  • Weight: 0.012 oz (0.34 g)
  • Dimensions: 0.23″ x 0.18″ (5.8mm x 4.6mm)
Klover MiK 09 LED Kit
Klover Mik 26 Tactical Kit

Headphones

Remote Audio HN-7506

“These surprisingly comfortable phones have been a big hit for professionals who want to protect their ears while monitoring the quality of their recordings. Sealing off outside ambience by as much as 45dB, the HN-7506 is designed to sound like the industry standard Sony MDR-7506, and allows the switch from one to another without loss of monitoring standard and reliability.”

Supplied with 6 foot, coiled cable with 1/4″ TRS connect with detachable 3.5 mm stereo mini plug.

Koss PRO4AA

“Koss Pro4AA headphones set the standard for full size professional headphones. They were introduced in 1970 as the first dynamic headphones to deliver true full frequency and high fidelity performance with impressive noise isolating capabilities.

Pro4AAs deliver superior isolation, accurate reproduction and sound intensity, and the excitement of a live performance with every recording. ”

Provided with an 8 foot, coiled cable with 1/4″ TRS connector

Klover MiK 09 LED Kit
Klover Mik 26 Tactical Kit

Reviews

There are no reviews yet.

Be the first to review “Klover MiK 16 Kit”
Contact Us

We're not around right now. But you can send us an email and we'll get back to you, asap.

Not readable? Change text. captcha txt

Start typing and press Enter to search

Klover MiK 26 TE parabolic microphone Kit with MM-1Klover MiK 09 LED Equalized XLR parabolic mic kit